This function is not used, since no power button is installed. In this case only the RAM is supplied with power. S3(STR): Option for writing the current state of the operating system to the RAM. Press the 'Y'-key and confirm with 'Enter'. In order to organize the current BIOS-settings, select the item 'Load Optimized Default' and press 'Enter'. my ex-friend did something to my computer then took it to get fixed from on of his friends-friend and when i got it back the system name is changed i think my proccessor got changed because all my pictures were gone and other pictures were in my computer when i press F10. Only a few functions are switched off and are available again at a keystroke +43/ (0)7662/6785, Plug in a PC-keyboard into the PS/2 keyboard socket and switch on the terminal. Phoenix-AwardBIOS CMOS Setup Utility asks for password it says invaild. The ACPI option (Advanced Configuration and Power Interface) is an extended PnP and power management function. For a restart the power supply must be interrupted briefly. In ATX mode the internal power supply unit of the controller switches off. In AT mode the power supply unit remains switched on when the system is shut down. ![]() Option for setting the power supply unit mode. Here a menu can be opened to select the IRQs for system wakeup.↑ ↓ → ← :Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:Helpį5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults Power-Supply Type Up to three timers can be set to restart system. If supports, will try to turn on VT-x and install HAXM. Here you can set the action of the power button: Delay 4 sec.: you have to press the power button longer than 4 sec to shut the system down. I want to check if my computer supports Virtualization Technology (VT-x). Setting options: NA (no allocation), 3 (allocated), 4, 5, 7, 9, 10, 11 Soft-Off by PWR-BTTN Activity on this line causes the computer to 'wake up' in order to receive a fax, for example. ChoosePOWER MANAGEMENT SETUPoption on the main menu, a display will be shown on screen as below : Phoenix - AwardBIOS CMOS Setup Utility. Using this simulation, users can get a better understanding of how to navigate, change values, and otherwise manipulate the Phoenix - Award BIOS. This option is used for specifying the interrupt line (IRQ) of a modem (if present). For example, in a standard (non-UEFI) Phoenix Award BIOS, in the Advanced BIOS Features section, you might see settings for First Boot Device, Second Boot. This page helps give users an online example of how to navigate through the Phoenix - Award CMOS setup. ![]() Be sure to save your changes before exiting the CMOS Setup. Then load the defaults by selecting Load Fail-Safe Defaults, Load BIOS Defaults, or whatever your BIOS manufacturer has named this function in your particular type and version of BIOS. If the frequency multiple or bus frequency are adjusted too high, the system may hang. This setting controls how long a harddisk must be left idle before it spins down. Enter the CMOS setup utility during the startup of your PC. To set the following 2 felds, the CPU speed must be set to Manual. ![]() Settings: Disabled (no energy saving function used), Min Saving (this setting is activated after 40 minutes and offers the lowest energy saving level), Max Saving (this setting offers the highest energy saving level). All system context except the memory context get lost. S3 (STR) Suspend to RAM: The state S3 is a deeper sleep mode. In this state no system context get lost (CPU oder Chipsatz) S1 (POS) Power on Suspend: The sleep mode S1 has a very low reactivation latency. For more information see BIOS-Inside / ACPI-Funktionen. ACPI normally has six states: system S0, S2, S3, S4, S5. Phoenix - AwardBIOS CMOS Setup Utility Advanced Chipset Features AGP Aperture Size 128 Item Help AGP Mode (Internal) Menu Level CPU to PCI POST Write Enabled Select Display Device CRT. This option offers two possibilities: S1 (POS) and S3 (STR). ↑ ↓ → ← :Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:Helpį5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults ACPI Suspend Type ![]() This menu is used for power management settings.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |